Polystyrene for leg armors

I've been working on Masamune's leg armor the last days but I haven't done a blog post about it yet. I'll write about it now so that I don't get one super long post.. and besides I've come to a point (read: I ran into a problem) where I must wait before I can continue working with them. *shrugs* Oh well, I'll write at least something now.

Okay, so I've had this roll of polystyrene since late November last year and on last Wednesday (3rd April) I finally started working with it. I've never worked with polystyrene sheets before and there doesn't seem to be so much talk about it being used for cosplay projects (I can find tutorials about styrene used for cosplay but not polystyrene..) on the internet either.. so with that said I had to do the trial and error approach to this one. Oh well, you won't learn if you are afraid to try something new so here goes!

Polystyrene sheet after being freed from most of the protective wrapping...

... and loose.

I don't remember the dimensions of my sheet but I'm pretty sure it was 1000x2000mm and 1 or 1,5 mm thick. Oh well, with the polystyrene rolled out I decided to check, well, how to cut it.

Here's the two candidates ~

It was pretty hard to cut, you had to use some force but it's possible to cut with ordinary (heavier) Fiskars scissors for example.
I took my leg armor patterns and drew one of them with a pencil on the polystyrene and cut it out.

One leg armor piece drafted on the material..

... and cut out.

Okay, I noticed pretty early it's hard to change directions during the cutting. You can curve if you do it little by little but any more noticeable/angled or sudden curves and you'll be cursing. Or well.. at least I was about to. Thank god Masamune's armor is pretty simple in shapes so I got by without further "perkele" storms.

Before finishing for the day I took a scrap piece of the plastic and went to check how well it would take spray paint. I didn't do anything to the surface prior to spraying and it took the spray like a charm!

Aaww yeeaah!

The next day (4th April) I took a scrap piece of polystyrene and went to test heat forming it outside with the heat gun and it was a...

... SUCCESS!
(and protection gloves are pop)

With the scrap piece shaping successful I took my actual armor pieces and gave them the same treatment. The only thing you have to be careful with during the heat forming is not to overheat the plastic or well.. it will melt and be ruined. You will notice during the heating when it's getting hot enough so its shape can be changed, just turn the heat gun off when you feel it loses some of its sturdiness and keep it in its new shape until it cools down. If the form didn't turn out as you wanted you can just reheat and reshape it.. but be careful because you might get these.. err.. "heatbumps". I got a few but they don't bother me.

Oh, also, I shaped everything with just my hands. You would likely get better results if you used some sort of mold in the shape you want the polystyrene to have when done. Because I shaped mine by hand no armor piece has the exact same shape to it.. they all are slightly different, it's noticeable when you put them on top of each other. But I had nothing that was usable as a mold so yeah, freehanded for the win ~

When heat forming I held the armor something like this

Tadaah~

Here's a comparison shot with a shaped armor piece (left) and an untouched piece (right)

I must say that compared to craft foam polystyrene keeps its new shape like mountain while it still remains as bendable as it was before. It's pretty fabulous; you can bend it if you apply some pressure but it will return to its shape when you let go.. unless heated, then it will stay in the new shape obviously. Oh, also, if you bend at some very thin point, like maybe 1 cm wide, then it might snap cleanly if you bend too much. Yes, I tried on a scrap piece and at least mine did snap.. then again it might vary depending on what thickness you have.

I went to cut out the remaining leg armor pieces (except the knee caps) and heat formed them. I gave each of them a somewhat pronounced groove in the middle. Next up was to paint them and again I made myself a makeshift working table ~

All leg armor pieces shaped and ready for painting

I gave them a coating of the same black spray paint I used for the arm guards.

After one coat of spray

I let them dry for the rest of the day because the 0 °C weather slows down the drying process. During the evening I moved my armors from the open "car garage" into the rather old summer cottage standing on our yard... I let them be there overnight.

The following day, also known as yesterday (5th April), when I woke up I went to the summer cottage to take my armors inside for a while... the summer cottage doesn't count as inside because it has broken windows and the door is half loose lol. I let the armors be inside and "warm up" for maybe 30 minutes before going outside to spray the inside of them.

Inside of the armors before painting...

... and after a coat of spray paint.

I let them dry for a few hours and when I went to check I noticed somehow some hairs had managed to get on the armor pieces and gotten stuck between the spray paint coats during the drying. They annoyed me so I peeled them off and...

... the paint around the hairs went with them. Fuck. :)

Oh well, it's the inside so no one will see it anyway.. and it just looks like some sort of damage so it just adds to the believability or something.. come on, Sengoku Basara is a hack 'n slash game series, no one would actually have perfect armor for long when you think about it. xD trolololo ~

After the inside paint had dried I gave the outside a second coating, there was a few spots where the paint wasn't even so yeah. After the painting was done I went to work with the knee caps but I will make a separate blog post about that later because I'm having some trouble with them right now.

Masamune arm guards pt.1

I've been working on the arm guards for Masamune the last few days and figured I could write a progress post now that I'm about half-way into the process. So well, back on last Monday (1st April) I cut out the pieces for the arm guards from craft foam, namely two "bottom" and two "top" parts.

One of the "bottom" parts cut out

With all the needed parts cut out I asked Jäätynyt Enkeli to come help me with the heat forming because hey, two pairs of arms are always better than one. So we went outside and one of us held the craft foam piece in its wanted form while the other one used the heat gun to form it. The first piece we finished looked like this after the heat treatment:

Tadaah ~

And this is what I had after we were done forming them:

Dem shapes ~

I must say craft foam, at least in my case, doesn't hold the shape really well.. it keeps the shape semi-well but I noticed it straightened itself out with time.. at least mine did. *shrugs* Oh well. I didn't do any more progress on Monday.

Yesterday (2nd April) I decided to try using fabric backing for the first time as a way to stiffen, strengthen and support the armor. So I went into the attic to check what fabrics we had that could possibly work; I wanted something smooth, something light-weight that had a bit of stretch. After looking around I found this one very dark blue very soft and nicely flowing knit-like fabric that seemed pretty cool. I took it with me back inside and cut out fitting pieces for the armors, making sure to have some excess just in case.

Fabric backing cut out

I then just took the craft foam armor pieces and glued the fabric on the side that would be against my body, obviously. I used your standard white universal glue and, in my case, that was Erikeeper. I just took a pencil and brushed glue all over the foam and then put the fabric on and pressed it and let it dry. I used a little bit too much glue on the first try because when I was applying pressure the glue "leaked" over the fabric. Well, now when I think about it it's not weird that it did.. the fabric is knit-like after all.. aka small holes. -.- Oh well, it made no difference so no harm done.

Fabric glued to the back side of the craft foam

I did this same thing for all the pieces and after they had dried completely I trimmed the excess fabric away.

Fabric backing to the right

Next step was to seal the craft foam. This step is optional (as well as fabric backing) but I always do it because otherwise you will be spending more paint on the foam because.. well, it's a bit like a sponge or something so it sucks in color a lot. It's better to just seal it because if you do you will get away with fewer coats of paint and posssibly a nicer result as well. Not to mention sealing the craft foam seems to give it a bit more strength too. I use a glue & water mix, aka diluted glue. I just use a normal white glue (Erikeeper, again) and mix it with some water until it's watery enough not to leave any pencil strokes when you brush it on.

Water & glue mix ready to be brushed on

And here's the foam pieces after their first coating, still wet
(you can notice at this point the pieces have lost pretty much all of their curving...)

And the remaining part of yesterday I applied shitlots of coatings; every time the earlier one had dried I put a new one. I think I coated them around 10 times, I'm not so sure, I didn't count. Today I put on a few more glue coats on the morning and then waited until stepdad got back home from a trip to town; he bought me some black spray paint, like I had asked yesterday.

The spray paint in question

I went outside and made a makeshift working table out of small wooden steps and cardboard. I put the foam armor pieces on top of the cardboard.

My makeshift working table ~

I then took the spray paint and shook it for some minutes before I sprayed away.

First coating...

Okaaay... my first reaction was something along the lines of "Oh god why didn't I use a black/white primer?" It's easy to be wise after the event.
I must say the first coating made me scared because the foam didn't seem to take the paint well at all and all sorts of "oh fuck don't tell me it won't work" thoughts appeared in my mind. I then thought that maybe I diluted the glue too much and/or didn't use enough coatings. I don't know, but I got nervous and waited a bit before I tried spraying on a second coating. 

Second coating...

The foam pieces seemed to take in the second coating better but the bright colors still shone through when you looked at them from certain angles and my hopes about this working as well as it had done with earlier projects sunk pretty low. When I looked at them my expression was like:

But I decided to let them dry outside for a while and came back an hour or so later to check. I was not surprised to find out they hadn't completely dried yet...  stupid 0 °C weather, takes forever to dry! Oh well, I decided to spray on a third coating just in case to see if they would turn fully black now.. if not I could just paint them over with an ordinary black paint and then try spray painting on top of that.

Third coating

Okay, my hopes for these arm guards are slowly recovering! I'm not so sure how they will look when dry but at least now the original color doesn't shine through much at all. Currently the pieces are in the sauna drying (mind you, sauna is power off xD) because at this moment it's about to get dark outside and the paint really doesn't dry well in the cold. Oh well, tomorrow I'll see how they have dried. Hopefully the paint will still flex with the foam when dry, it seemed to bend just well without cracking while I tried bending them when they weren't completely dry. Here's to hoping.

More progress later.

Masamune armor patterns + Craft foam heat forming test!

Back on last Friday I started drawing the patterns for Masamune's leg armor and arm guards. Basically I just looked at some references, took measurements and improvised.

Just one of my many Masamune references

After I had made a pattern I tried it around my leg/arm to check if it fit like I wanted and so on. Here's some pattern photos:

Started drawing the first pattern (leg armor)

To make sure that my patterns were symmetrical I drew one side, cut out half of it, folded it over and traced it to make the other half identical.

Leg armor pattern (front curves at top, back doesn't, hence the lines) with knee cap

Top arm guard pattern

I had to redo the lower arm guard pattern a few times because I noticed that the arm guards won't lay like straight on "top" and "bottom" of your arm.. they'd be angled a bit diagonally or eh, so that the spike of the top arm guard is turned more towards your elbow. If that makes sense.

Original pattern wasn't wide enough at top so I widened it..

Then I noticed it was maybe a bit too wide so I made secondary unfilled lines just in case...

.. but I ended up cutting them off and modifying the pattern a third time.
The final pattern is the one with the red marker on top of it.

Okay, enough of patterns. Yesterday I went to town to buy some craft foam for the project and the more I thought about it the more I felt like I wanted to make the arm guards out of craft foam instead of the polystyrene sheet.

Craft foam sheets!
(well, they are pretty bright colored but you can paint over them so it doesn't matter..)

Today I then traced the top arm guard pattern on a sheet of craft foam and cut it out.

After tracing

I didn't cut out more than one piece because I wasn't sure how to go about forming it.. or well, more like I've never done it before. I knew it was possible to form craft foam into different shapes with a heat source, like a stove burner or heat gun for example. The stove burner option wouldn't work at my home and I wasn't sure a hairdryer would do the trick so I asked stepdad if he happened to have a heat gun... and he did! Wohooo!

I took a few earlier scrap pieces of craft foam and went outside to try heat forming the foam into a new shape.

Heat gun, gloves for protection and a few scrap pieces

There was a metal rod protruding from that working table I used.. so I decided to use it as a form to test shaping the craft foam on. I just put on the gloves, rolled the craft foam piece around the rod and kept it in place with my hand while I applied heat. When it seemed like the craft foam started to get soft/floppy I turned off the heat gun and kept the foam in its new shape until it cooled down.. and this was the result:

It works! :DD

A few more tries later I had this:

The one to the right is the first try, second in middle and last try to the left
(those cuts were there before, they are not cracks that happened during the heating)

I must say while I formed the last one my hand slipped from keeping it in place on the rod and so it got a slight mark from my hand because it hadn't cooled down enough to regain it's normal.. consistency. I need to be a bit more careful with the actual arm guards then so that their surface stays nice and even. Oh and yeah, I plan to make it tomorrow!

Masamune try-on, this is what I have so far!

Today I decided to put on everything I have ready, so far, of my Masamune cosplay.. just to see how it all fit together. All armor and weapons and some smaller details are missing.. like tabi socks. I haven't tried all the at-this-moment-ready parts on before so this was the first try! I'm surprised at how flattering this thing looks on me.. I was pretty sure I'd look horrid but glad to see I was proved wrong!

Here's some photos! Oh, and yeah, used a mirror for help so they're all mirrored.
Also I didn't find the eyepatch so excuse me Masamune regained his sight for a while lol.

Today I also started making the patterns for Masamune's leg armor and arm guards. But I noticed I don't have enough craft foam at home.. which I will need to make prototypes to check that the patterns are okay and maybe also use it for the actual armor. I will go to town tomorrow and buy some. More about the armormaking then! See you all!

One-eyed Dragon rubber pants

I've actually been working on the pants for Masamune since last Sunday but I'm going to post about it now that I'm finished instead of posting multiple short updates.

Okay, so on last Sunday (17th March) I decided on what pants pattern to use.. I had been very unsure about this for quite some time. I found an okay pattern at one of these sewing magazines mom occasionally buys. I just followed the instructions in the magazine and traced out the parts I needed from the pattern sheet.

So.. much.. patterns...

But I managed to find, trace and cut out what I needed

That Sunday I didn't do anything else. On last Tuesday (19th March) I wondered if I should do a prototype version.. you know, like a mock-up of cheap fabric to check that everything works before using the real fabric. But I didn't really feel like making a prototype so I just measured the patterns and compared them to myself and it seemed okay.

Yesterday I started the progress for real. First up was of course to put out the patterns and cut the fabric. I must say I had pretty much just enough fabric left for the pants.. the rest was used for the coat. Oh, and I saved all slightly bigger scrap pieces in case I can use them for Masamune's "wings" between his sword sheaths.. but more about that later.

Here's a few photos:

Patterns pinned in place..

... and cut out.

But while cutting I managed to prickle my hand on a pin and I didn't notice the blood until after I was done cutting.. at least I got nothing on the fabric, that would have been a bother..

Most common damage in this hobby I guess..? xD

With the front and back pieces cut out I went to start the sewing. This time I would use the overlock machine, it makes life a lot easier.. and quicker.

First thing to do was to take both front pieces, put them right sides against each other and sew them together at the.. err, crotch. xD I did the same to the back pieces of course.

While sewing..

Next step was to sew the outer seams closed. Nothing special.. I put the front and back pieces against each other, right sides together and sewed on the wrong side of the fabric.

Outer seam sewed... turns out one side has a slightly longer leg by the way

With the outer seams closed I could now go and try the pants on and see if I could even get them on because.. well, almost always when I sew something I worry I have underestimated my walrusness when measuring.

I must also mention that yesterday I wore kimono all day and well.. I didn't feel like changing just to check for a few seconds if the pants would fit...

Tsädää!
If they fit over a kimono at least they aren't too small! :DDD

Knowing the pants weren't too small I went ahead and closed the... err, inner seams and crotch area or whatever to call it.

After I had passed the crotch seam..

When I had finished sewing that part I checked that everything was alright and that the stitching had caught on both sides of the pants... which it hadn't.

Before

After

Next thing I did was that I evened out and hemmed the pant legs. The overlocking machine makes things easy because it cuts the fabric too so I didn't have to cut the excess length off myself.

Fixing a pant leg...

After that I had to add a strip of fabric to the top of the pants to keep them from falling off I moved around for a while. I had saved a bit of the fabric for this purpose back when I cut out the pants.

This was the piece that was left
(yes, I like me some Pepsi)

After I had trimmed it to a 13 cm width

After i had cut it shorter

With that done I went to sew the ends together so that I got a tube, like this:

Then I just folded it in half and put it on top of the pants upper edge, right sides together. I figured I wouldn't need to add an elastic into the "tube" because the fabric stretches a bit; instead I just cut it a bit shorter than the measure of the pant's circumference and stretched it to match with the pants while I sewed it on.

Oh well, when I was half-way with sewing the tube to the pants the overlocking machine decided to quit. Mom tried to check what was wrong with it but it just didn't want to cooperate anymore for Saturday, despite some tries to get it to sew normally.

Half finished waist-tube-thingy.. you can see to the left where it stopped sewing properly

I didn't work anymore for Saturday and so today (Sunday) I did the last fixes. I started by trying to get the overlock machine to work but it just kept doing bad stitches or no stitches at all. Mom came to help and re-thread the thing a few times until it finally worked again. I must say when I tried to re-thread it (first time ever) I noticed how this thing certainly wasn't made for left-handed people. Dx Oh well.. we got it to work so I finished sewing the rest of the tube on.

Finished waist tube thing..

With only the pant legs to fold I went to try them on. I must say they are surprisingly okay to wear.. except that when I move they make this rubberish sound.. mom actually dubbed them "rubber pants". xD Oh well, here's a photo:

I just had one thing to do now.. fold and sew the pant legs. They were a bit too long so I folded them over twice to get them to a good length. Of course I used a normal sewing machine for this.. can't do a straight stitch with an overlock...

Folded and ready for sewing..

Finished!

And with that my pants for Masamune are done. Next time I'll either do some small stuff like the gloves/tabi or start with the armor making. We'll see.

See ya!